Kategori
- Analisa Struktur Tanah
- Analisa Struktur Beton Bertulang
- Analisa Struktur Baja & detailing
- Analisa Struktur Jembatan
- Analisa Struktur Kayu
- Dinamika Struktur
- Perhitungan Beban Angin
- Perhitungan Hidrologi
- Analisa Struktur Tertentu dan Tak Tentu
Perhitungan Struktur
- -Q-Torsion Design
- ACI 350 & ACI224R-01 Rectangular Section Flexural Crack Width Control
- ACI 350.3-06 Seismic Loads for Liquid-Containing Rectangular RC Tank
- AISC-ASD89 calculation for Beam-Column member
- Analysis for Flat roof systems in structural steel
- Analysis of Pile Groups with Rigid Caps
- Anchor Reinforcement
- Anchor Reinforcement Metric Version
- Appendix D – Anchor Bolt Anchorage
- Appendix D – Anchor Bolt Anchorage AC! 318
- Application for Generation of Height Span Charts Gable Frame Sheds
- ASCE 7-10 Load Combinations
- ASCE71OW – ASCE 7-10 Code Wind Analysis Program
- Axial load capacities of single plates per AISC
- Beam Investigation
- Beaming Capacity for 2006 International Building Code
- Bored Piles Wall and Ground Anchors
- Bridge Concrete Deck Design
- Bridge Design and Analysis
- Calculator assessment of timber structures to AS1720
- Calculator for assessment of cold formed steel structures to AS4600
- Calculator for assessment of steel structures to AS4100
- Calculation of Plane Truss
- Cold Formed Steel Sheds Australia Height Span Limits of C-Sections
- Composite Column
- Concrete Beam Design (CSA A23.1-94)
- Concrete slabs on grade
- Concrete Special Structural Wall ACI 318-08
- Corbel
- Corbel Design (CBDM)
- Design of Prestressed Double Tee Beams
- Design of RCC Trench
- Earthquake Lateral Forces
- Elastomeric Bearing Design
- Foundation Support of a Tank
- Gable Canopy to Australian Codes
- IBC 2006 Seismic Calculation
- IBC2000E – Seismic loading analysis for buildings and various non building structures
- IBC2003E – Seismic loading analysis for buildings and various non building structures
- IBC2006E – Seismic loading analysis for buildings and various non building structures
- IBC2009E – Seismic loading analysis for buildings and various non building structures
- Loads Beam Slab and Spread Footing
- Loads beneath Rigid Pile Caps or Rafts
- Mast – Supporting Guyline
- Member Design – Reinforced Concrete Beam B58110
- Micropile Structural Capacity Calculation
- PCI Stud Tension Breakout
- Pile design
- Prestressed Girder Design
- RC Element Design to Indian Standards
- RC Rectangular Section Design to BS811O Part 1 & 2
- Re Bars
- Re Bars (318 -05)
- Re Bars (318-08)
- Re Bars (318M-05)
- Rectangular HSS & Box Shaped Members
- Rectangular HSS & Box Shaped Members – Combined Bending Shear and Torsion
- Rectangular Section Flexural Crack Width Control
- Reinforced Concrete Staircase ACI-318-08
- Reinforced Concrete Circular Columns
- Reinforced Concrete Pad Footing AS3600 Compliant
- Reinforced Concrete Rectangular Columns
- Reinforced Concrete Sections to BS 8007
- Retaining Wall Calculation
- Retaining Wall Design
- Retaining Walls
- Roof Deck
- Sheet Piling
- Slab Design Base on BS Code
- Snow Loading on FLat Roof
- Soil Bearing Capacity Calculation
- Standard hook bars in tension for AC! 318-08
- Steel Roof and Floor Deck
- Stresses Beneath Pads Under Eccentric Loads
- UBC97 Earthquake Lateral Forces
- US Steel Sheet Pile Design
- X-bracing Design
- All Structural Section Tables
- Beam on Elastic Foundation Analysis
- Concrete Design
- Design of Structural Elements
- Engineering with the spreadsheets
- Footing Design
- GoBeam
- International Lateral Loads
- Lateral Programs
- Masonry Design
- Misc Spreadsheets
- Other Structural Spreadsheets
- RC Stair design according to BS 8110
- RC Spreadsheet v1
- RC Spreadsheet v3
- RC Spreadsheet v4a
- Response Spectrum Workbook
- Steel Design Spreadsheets
- Structural Design Spreadsheets
- Structural Tool Kit 3.37
- UBC Seismic Calculations
- WSBeam
- AASHTO LRFD Slab
- AC1318-08 RC Beam
- Aluminum Capacity Design
- Aluminum Rectangular Tube Design
- Beam Analysis Spreadsheet
- Beam Analysis Spreadsheet (Metric)
- Beam Design Functions
- Beam Reactions
- Beam with stress
- Beams
- Beams on Elastic Foundation
- BS 5950 Circular Hollow members
- Built-in beam with 2 symmetric point loads
- Checking Steel Members with Various Reinforcements
- Continuous Beam Analysis (up to 4 spans)
- Continuous Concrete Beams
- Crane Design Guide to BS5950
- Curved Beams
- Design of Rectangular Column
- EC3 Calculations
- Enhanced Beam Analysis and Design
- Flexure and Torsion of Single Angles
- FRP Reinforcement of RC Beams & Slabs
- Grating Aluminum Beam Design
- Historic 1939 UK Steel Section Properties
- Indian Steel Sections
- Influence lines in continuous beam
Detail Struktur
- AISC-LRFD HSS Bracing Punch Plate Connection
- AISC-LRFD-HSS-Virendeel Connections
- AISC-Weld calculation for built up beams
- Analysis and Design of Steel Columns & Beams
- Analysis of steel beam end connections using double clip an
- Analysis of steel beams subject to concentrated loads
- Analysis of Steel Column Base Plate
- Anchor Bolt anchorage
- Angle Seat Detail
- Angle Section Properties
- Angle type tension fitting
- Base Plate analysis
- Bolted Connection Angle Brace Tension
- Bolted End Plate Splice Apex Connection of Portal Frame
- Calculation for mixed concrete-wood floor
- Channel type tension fitting
- Check of Tubular Members as per API RP2A – LFRD Code
- Beam Connections using clip angle
- Coped W-Beam seat
- Dayton-Shear-Reinforcement-System-For-Round-Columns
- Dayton-Shear-Reinforcement-System-For-Square-Columns
- Deck Slab
- Design of anchorage for underground storage tanks
- Design of Moment Connection
- Design of Plate Elements
- Design of Spread Footing
- Embedment Strength of stud plate
- Gusset Plate Connection for Truss
- Load Combinations
- Mast Design
- Member Design – Steel Beam Column design to BS5950
- Method of Jet Grouting
- Monorail Design
- Offshore Tubular Joints Punch Check as per API-WSD
- Plates straps and rivets
- Pole Foundation IBC 2003
- Pre-Cast Column Connection Design
- Precast Concrete Plank
- Rectangular Spread Footing Analysis
- Rectangular Steel Bar Design
- Roof Purlin Design
- Semi-Circular Tension Fitting
- Shackle Calculations
- Shear Friction ACI 318-02
- Shear Lug Design
- Simple Shear Connection Design AISC
- Snap Fit Beam Calculator
- Spread Footing_vl.04
- Stair Stringer Design
- Steel Beam Bearing Plate Design
- Steel Beam End Connection Design
- Steel Beam with Web Openings
- Steel Reinforcing Platefor Masonry
- Stress in a plate due to a point load
- Two-Way Slab Design to BS 8110
Perhitungan Struktur Tanah
- Account The Shear Size Of Bored Piles
- Analysis of a sheet pile wall
- Analysis of a slip on a long natural slope
- Analysis of Gabions
- Axial and Lateral Load Piles (FEM)
- Bearing Capacity
- Bore Pile Design BS 8004
- Bored Pile Deep Foundation
- Bored Piles For The Analysis of Layered Soil
- Boring Log
- Cantilever retaining wall analysis
- Concrete Box Culvert analysis and Design
- Drained Strip Foundation En1997
- Immediate Pad Footing Settlement
- Lateral pressure against retaining wall due to surcharge loads
- Pile Capacity Calculation
- Reinforced Retaining Wall Design
- Simple Geotechnics Calculations
- Soil Arching – Braced Excavations
- Surcharge Loads Tips – 2
- Surcharge Loads types
- Surcharge Point Loads
- Tunnel Design – Initial Support with Steel Liner Plate
- Wall Pressure Analysis
Perhitungan Analisa Struktur Tertentu & Tak Tentu
- 2D Frame Analysis
- Beam Analysis with FEM
- Bolt Connection Analysis with FEM
- ExcelFEM_ 2D (for Excel 2003)
- Excel FEM_ 2D (for Excel 2007 & Excel 2010)
- Exc eIFEM_ 3D (for Excel 2003)
- ExceIFEM_3D (for Excel 2007 & Excel 2010)
- Truss Analysis with FEM
Kursus Online SAP2000 - Bersertifikat
Hanya Rp 299.000
Ayo Gabung dengan lebih dari 114 Peserta Lainnya
Download Koleksi Ribuan Excel Teknik Sipil
Cara Download Gratis
